How To Clean Dyson V11 Filter

Whether you're a clean junkie or someone getting the chore done only because, Dyson vacuums are a must-have!

Along with their peak-notch performance, they offer a multifariousness of advanced features to make your lives easier. Their reliable customer back up is an added bonus too!

Nevertheless, taking good care of your Dyson vacuum is mandatory. Like any other electronic equipment, unless you spend your time and effort behind their maintenance, they're leap to start malfunctioning.

Often times while getting the cleaning filter all spotless as new, users take experienced their V10 or V11 models to terminate working.

But what should be washed when such a situation arises? Hang on and read till the end to notice quick fixes to this always then natural trouble.

Dyson V10 and V11 Not Working later Cleaning Filter

Dyson V10 and V11 Not Working after Cleaning Filter

Filter is Still Wet

This is a mistake most V10 or V11 users tend to brand afterwards washing the cleaning filters of their Dyson vacuum.

You need to await a little while patiently to let the filters dry out upwardly all the manner.

Unless yous do so and install information technology while it's all the same somewhat wet, your vacuum will non work at all.

This is due to the fact that a wet filter will restrict proper airflow through the filter. And when this happens, the Dyson vacuum volition shut itself down to prevent whatever farther impairment to the device.

In instance you notice your filter isn't fully dried up, remove it right away and let information technology dry overnight on a clean surface.

If possible, plan ahead and continue it aside to dry for around 24 hours. This way, y'all'll exist risk gratuitous. Please don't fifty-fifty think of using it with a wet filter as it volition simply bring y'all miseries!

Don'ts:

Merely in case you need to do an instant cleaning but your filter is still somewhat moist with h2o, avoid using a pilus dryer or a estrus gun! Almost DIY tricks suggest the apply of hair dryers and as such for these purposes, merely it will merely ruin the quality of your clean filter.
Do not put it under direct sunlight or scorching heat under whatsoever circumstances. Doing and then volition cause your clean filter to dry upward, but in the process, it will cause wears and tears too. And then, it's a big no! Instead, merely leave information technology in a clean place with optimal airflow and be patient.

Filter is Not Installed Correctly

More often than always, Dyson vacuum users have fabricated this error endless times. When the filter isn't attached properly to the vacuum, it will obviously not work.

However, some other way to know whether this is the issue with your Dyson V10 or V11 is the indicator light.

Whenever the filter is not correctly installed or has clay stuck onto it, it will flash a bluish light on the side when pulling the trigger. This is entirely because incorrect installation or droppings volition non allow a totally sealed interior or "vacuum" required for the vacuum to role.

To overcome this problem, firstly remove the filter from your V10 or V11. Then head off to inspect the filter expanse and look for debris aggregating. If there's any, clean it off with a soft cotton cloth.

In example that isn't the result, install it properly post-obit these steps- Fit the filter into identify, give it a piddling button and twist it clockwise.

Once y'all hear a click, end right then and at that place. And you're done, voila! If you yet have queries or confusion, you lot can always look into the sticker at the back of your filter unit of measurement. Properly following the instructions will become you done in no time.

Dyson V10 Not Working after Cleaning Filter

Worn Out Filter

Assuming that you're a regular user of your Dyson V10 or V11, the clean filters will eventually wear out due to heavy usage.

At most, these filters will last for 2 years at a stretch upon regular cleaning load. Yet, in case you rarely use yours, they'll last much longer.

These clean filters in Dyson vacuums habiliment out with fourth dimension especially if you tend to vacuum in lots of fine clay and debris.

That's considering regular dirt getting stuck on the filter will saturate the fine pores and restrict proper airflow through information technology. Since these filters are manufactured to be hand-done and reused, washing them with cold water at regular intervals volition do the task.

Nevertheless, if the filter has served y'all for about 2 years and your vacuum won't work now, it'southward time to get a new one! Make sure to order yours from the official Dyson website and not from any 3rd-political party sellers.

It's always better to spend on a reliable source than putting your vacuum at gamble.

Technical error: Motorhead Failure

With all the obvious troubleshooting done and dusted, permit's motion on to some technical stuff, shall we?

From time to time, users have experienced motorhead failure on their Dyson V10 or V11.

This may be a result of heavy usage or lack of following instructions properly. As we mentioned before, installing a moisture clean filter and trying to make it work may also put your Dyson at risk of motorhead breakdown.

When the water aerosol from the filter keep entering into the motor, it gets damaged similar whatever other electronic device. Makes complete sense, right?

Only what should you do when this happens?

The only manner out of this problem is to get the unabridged motor replaced. For this, if you lot're somewhat a technician yourself, just DIY your way through information technology.

In example you desire to go it replaced past a professional, you tin can always go ahead and contact the Dyson customer support center.

If that's not possible, simply take your V10 or V11 to a nearby local appliance repair store and get information technology fixed right away!

Dyson V11 Not Working after Cleaning Filter

Obstructions Inside the V10 or V11

Occasionally, whenever the Dyson vacuum starts to act upwardly or stops operation, the users tend to clean the filters just. However, many times you may overlook dirt accumulation on other parts of the vacuum.

If any such blockage builds up inside the Dyson, it will beginning pulsating whenever you attempt pulling the trigger.

At whatsoever moment, if you feel your V10 or V11 pulsating, it'south the device's way to notify y'all of ensuing internal damage.

Should this happen, brand sure to follow the below steps,

Remove all the parts from your Dyson vacuum in one case yous have cleaned the filter unit of measurement.
Thoroughly examine the wand, the brush bar and inlet for whatsoever signs of clay obstructions.
In case you lot practise find any, clean them off instantly with a moisture cotton wool cloth or a brush. However, brand sure to advisedly practice the job without dissentious any parts.

Doing this, the airflow inside the vacuum will be maximum and you'll get a skillful as new Dyson V10 or V11 at your disposal.

Now that we're almost at the stop of our troubleshooting problems, let'due south head on to something else.

To increase your Dyson V10 or V11 vacuums' shelf life and make the batteries and suction power terminal longer, here are some tips from u.s.a. to yous,

Ever plug off your vacuum after each utilise.
Recheck the cleaning mode before each use and change accordingly if necessary.
No matter what, try to store your Dyson vacuum at store temperature.
Brand certain to make clean the reusable filter from fourth dimension to time.
Earlier choosing which vacuum stick to use, have the cleaning surface into consideration.

With this, we have reached the end of our advice on what to do when your Dyson V10 or V11 stops operation after filter cleaning. In case y'all do end up facing any other issues, make sure to contact Dyson client care for an immediate fix. Nonetheless, always maintain your vacuum for maximum output and a longer lifetime. Promise you have a proficient 24-hour interval!